Foam Pro Insulation technician in a red shirt masking a door with plastic sheeting inside a wood-framed building before insulation work

Walls, ceilings, remodels and new builds

Fiberglass Batt Insulation in Phoenix, AZ

Pre-cut fiberglass batts fitted by our own family crew into open wall and ceiling cavities across the Valley. Clean work, tight fit, and a straight quote the same day.

Same-day quotes
AZ ROC #363201
Our own crews, never subcontracted

Get a Quote Call (928) 331-8400

Is fiberglass batt insulation right for my Phoenix walls and ceilings?

Fiberglass batts are pre-cut blankets that fit snugly between studs, joists and rafters. In the Phoenix metro they are the practical choice for open wall and ceiling cavities, whether you are gutting a room in a remodel, finishing an addition or framing a new build. Batts give you R-13 to R-15 in a standard wall and R-30 or more in a ceiling the moment they are in place, with no equipment to set up and nothing to wait on.

Arizona heat makes the barrier matter, since summer attics can reach 150 F. Foam Pro Insulation is family-owned, and our own crews cut and fit every batt. Gaps and squeezed batts waste R-value, so we trim each piece to its cavity and seal air leaks first. If a cavity is closed up, or an attic needs more coverage, we will tell you when blown-in insulation or spray foam is the better call.

Why homeowners pick batts

Six reasons batts work well in Arizona homes

Batts balance performance, cost and speed when the framing is open and reachable.

Instant R-value

R-13 to R-15 in walls and R-30 or more in ceilings, the moment the batts are in.

Budget-friendly

A cost-conscious way to insulate open cavities well without a big spend.

Great for retrofits and new builds

Fits open framing in remodels, room additions and new construction.

Fire-resistant

Fiberglass is naturally fire-resistant, an extra layer of protection in the wall.

Sound dampening

Helps quiet street noise and sound traveling from room to room.

No settling

Properly installed batts hold their shape and coverage in the cavity.

How we install

Our batt installation process, start to finish

Walk it and quote it
We look at the cavities, measure, and check for air leaks. Quotes are same-day, so you know the plan right away.
Protect your home
Drop cloths and plastic sheeting go down before any work starts, so living areas stay clean.
Seal, then fit
We seal gaps and penetrations first, then cut each batt to its cavity so there are no voids or squeezed spots.
Check and clean up
We confirm full coverage and depth, then remove all debris before we leave.

Want to know what your attic needs first? Book a free thermal-imaging attic inspection. It takes about 30 minutes and we show you the photos.

APS and SRP rebates

We help you go after your utility rebates

Utility rebates can take some of the sting out of an insulation project. We help Valley homeowners with APS and SRP insulation and duct rebates, and we will tell you which programs fit your project before work starts. Eligibility and amounts are set by the utility, so ask us what applies to you.

Batts pair well with other work that stops heat from getting in:

For builders

Volume pricing for builders

Framing a run of homes or a large addition? Builders get volume pricing on batt insulation from our own crews, not subcontractors. Tell us about your project and we will quote it.

Get a Builder Quote

Questions we hear

Fiberglass batt insulation questions, answered

Where does batt insulation work best in a Phoenix home?

Batt insulation works best wherever framing is open and easy to reach, such as wall cavities in a remodel, an addition, a garage conversion or new construction in Phoenix. It also suits ceiling cavities. Once drywall is up and a cavity is closed, another method may fit better, and we will say so.

Should I choose batts or blown-in insulation?

For a Phoenix attic floor, blown-in insulation usually covers evenly around wiring and ducts. Batts shine in open wall and ceiling framing. Many homes use both. A free thermal-imaging attic inspection shows what you have now, and we recommend the better fit instead of pushing one product.

How much does batt insulation cost in Phoenix?

Batt insulation in Phoenix is quoted by the job, because the square footage, cavity size and target R-value all change the price. We give same-day quotes so you can plan without waiting. Builders working on multiple homes get volume pricing, so mention your project size when you reach out.

What R-value will I get from fiberglass batts?

Fiberglass batt insulation in Phoenix typically gives R-13 to R-15 in a standard wall and R-30 or more in a ceiling. The result depends on cavity depth and how well each batt is fitted, so we cut every piece to its space and seal air leaks first to protect that R-value.

Do you install batt insulation outside Phoenix?

Yes. Our family crews install batt insulation across the Valley, including Glendale, Scottsdale, Chandler, Mesa, Gilbert, Peoria, Surprise, Goodyear, Buckeye, Queen Creek and more. Check our service areas for the full list. Every job is done by our own crew, never subcontracted.

Ready to insulate your walls and ceilings?

Tell us about your remodel, addition or new build and get a same-day quote. We are available 8am to 10pm, 7 days a week. Call or text.